Showing results: 196 - 210 of 316 items found.
-
M9161D -
Keysight Technologies
The Keysight M9161D PXI Dual SP4T solid state switch module provides an ultra-long cycle life, fast switching speed and high isolation, all within a single slot enclosure.
-
-
M9131A -
Keysight Technologies
The M9131A is a high-density, general purpose switch with 64 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights, or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100 Vrms and 1 A, with up to 3 W maximum power. Choose from the durable connector block or standard cable connections.
-
40-194A-001 -
Pickering Interfaces Ltd.
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
40-194A-002 -
Pickering Interfaces Ltd.
The 40-194A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
CPCI-ISC8 -
ALPHI Technology Corporation
The CPCI-ISC8 is an intelligent DSP based serial communication board. This 3U board is based on the CPCIIPC product and has been modified to remove the IPinterface and to support additional I/O features. The CPCIISC8 provides mechanical support and the electrical interfaces for an I/O mezzanine board. Multiple CPCI-ISC8 boards may be installed in a single system.
-
PXT(e)1741 -
VX Instruments GmbH
Easy linkage of various external modules to the PXI(e) trigger busHigh configurable trigger matrix12 independent configurable trigger linesInputs/Outputs compatible with 5 V TTL standardSoftware controlled triggering of any target device
-
VX3701 -
VX Instruments GmbH
With so-called synchro/resolver cards, rotation angle sensors that work according to the synchro/resolver principle can be measured. Depending on the angle of rotation, these generate a sine and cosine signal, in order to determine the position and direction of rotation.
-
Bloomy Controls, Inc.
Bloomy's 8-Channel Load Module provides isolated current and voltage measurements for eight on-board 5W loads or for eight off-board 120W loads. With built-in switching for calibration and fault injection, the module provides unsurpassed capability for Mil/Aero applications. The module also provides switching and connections to allow switching between a real load (e.g., actuator, valve, etc.) and the simulated load.
-
42-890-005 -
Pickering Interfaces Ltd.
The 40-890 (PXI) and 42-890 (PXIe) range of PXI microwave modules allows users to specify the mix of relay types, frequencies and quantities based on the application requirements within the capabilities of the module driver card. Choose from the extensive relay selection already available in the Pickering microwave range to create a flexible solution.
-
40-890-002 -
Pickering Interfaces Ltd.
The 40-890 (PXI) and 42-890 (PXIe) range of PXI microwave modules allows users to specify the mix of relay types, frequencies and quantities based on the application requirements within the capabilities of the module driver card. Choose from the extensive relay selection already available in the Pickering microwave range to create a flexible solution.
-
40-192A-012 -
Pickering Interfaces Ltd.
The 40-192A-012 is a PXI fault insertion switch using solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test
-
40-193A-001 -
Pickering Interfaces Ltd.
The 40-193A-001 is a 7-Channel Fault Insertion switch with one fault bus, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
40-193A-002 -
Pickering Interfaces Ltd.
The 40-193A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
iW-RainboW-G47V® -
iWave Systems Technologies
AMD Xilinx’s VU13P, VU11P, VU9P, VU7P, VU5P Virtex Ultrascale+ FPGADual 64 bit, 4GB FPGA-DDR4 with ECC (Upgradable)31 channels of FPGA GTY transceivers up to 32.75Gbps1Dual ARM Cortex-A7 core processor of 1.2GHz speed32bit 2GB DDR4 for CPU with ECC128MB QSPI Flash & 256MB NOR Flash3U VPX Connector (P0+P1A & P1B+P2A)8 Optical transceivers through MT Ferrule Connector (P2B)